Hi,
The advisory states the following:
Note: The HP D2220sb Storage Blade is only supported with one of the two embedded storage controllers on the HP ProLiant BL460c Gen 9 Server:
Hope either of the above controllers are being used to connect to the HP D2220sb Storage Blade.
If so and the issue is still not resolved, then contact HP Support for further assistance.
Regards,
Vijayasarathy
Thank you for your reply.
I was one more try bellow,
* Already update firmware BL460c Gen9.
1. BL460c Gen9 shutdown power off.
2. Remove D2220sb from enlosure bay.
3. Power on BL460c Gen9 , entry to RBSU and Restore Manufacture Default Settings.
4. Reboot server only BL460c Gen9 and shutdown and power off.
5. Insert D2220sb to enclosure bay and wait LED to steady green lit.
6. Power on BL460c Gen9 server.
but not recognized D2220sb.
ummm....
Hi,
The setting is:
RBSU -> System Default Options -> Restore Manufacture Default Settings
One can always settings in RBSU and save them as System Default Settings and when there are further changes made to the RBSU configuration and there are issues, the System Default Settings can be used to switch the server to the settings which were saved so.
Restore Manufacture Default Settings resets the settings to factory defaults. In this instance please use this option.
Regards,
Vijayasarathy
Thank you for your Information.
but, I'm already read that Advisory and I can't fix my problem of do'nt recognize D2220sb by BL460c Gen9.
Step.2 of Advisory,
~~
Clear the ProLiant BL460c Gen 9 Server Blade NVRAM using Platform Configurator via ROM-Based Setup Utility (RBSU) and reboot.
~~
This mean is
RBSU -> System Default Options -> Restore System Default Settings
or
RBSU -> System Default Options -> Restore Manufacture Default Settings
It is correct?
If not and other operation is required then please step of Clear the ProLiant BL460c Gen 9 Server Blade NVRAM.
Hi,
Please refer to this advisory that has been released addressing this issue for further information.
Regards,
Vijayasarathy
Thank you for your information!!!
I was updated my BL460c Gen9 server firmware and try to connect D2220sb,
but don't recognized D2220sb storage via Smart Array P244br controller.
P244br's firmware update latest version but this is not fix.
c7000 enclosure bay 7 = D2220sb
bay8 = BL460c Gen9
Hi guys,
Its the 31st March today, I've had a good search of the BL460c Gen9 support advisories and knowledgebase and didn't see any announcement about how to get the Gen9 to support the D2220sb . Is this forthcoming or should I seriously start thinking about trading my Gen9s for Gen8s? I've got a load of G1/SB40c that are W2K3 and getting cranky with age so I'm under a lot of pressure from my boss to get them migrated before the OS or hardware dies.
Thanks!
Hi,
The HP D2200sb Storage Blade is supported with HP ProLiant BL460c G7 Server Blade. For confirmation refer to section "Additional Options > HP Storage Blades" in the server Blade's QuickSpecs.
Hope this helps!!
Regards,
Vijayasarathy
Hi Supporter,
Could be used of D2220sb for BL460c Gen7? Have anyone to try that? Is it workable or not?
Thanks.
The D2220sb will be supported on March 30 with the annoucement of a new array controler that we need to reside in the parrent server blade. Existing D2220sb storage blades in the field can have their Firmware flashed in order to add support for Gen9 server blades that include the new array controler.
hope this helps.
Hi,
Going through the server's and the storage blade's QuickSpecs, I do not find them to be a supported configuration.
Regards,
Vijayasarathy
Thank you very much for your reply.
One more question,
Now, What Storage blade is supportable (supported) BL460 Gen9 server blade?
Nothing??
Hi,
Neither the HP D2220sb Storage Blade QuickSpecs mention support for HP ProLiant BL460c Gen9 Server nor HP ProLiant BL460c Gen9 Server's QuickSpecs mention support for the storage blade. This indicates that they have not been offically test together as of date.
The HP D2220sb Storage Blade supports the following Gen8 Blade servers though:
Regards,
Vijayasarathy
C3000 or C7000 enclosure quick specs PDF included following words.
---
The D2220sb Storage Blade delivers direct attached storage for c-Class Gen8 and greater server blades
---
But, D2220sb 's documents not found keyword "Gen8 and greater" or "Gen9 supported",
Can I use with D2220sb and BL460c Gen9 ?
Hi,
The advisory states the following:
Note: The HP D2220sb Storage Blade is only supported with one of the two embedded storage controllers on the HP ProLiant BL460c Gen 9 Server:
Hope either of the above controllers are being used to connect to the HP D2220sb Storage Blade.
If so and the issue is still not resolved, then contact HP Support for further assistance.
Regards,
Vijayasarathy
Thank you for your reply.
I was one more try bellow,
* Already update firmware BL460c Gen9.
1. BL460c Gen9 shutdown power off.
2. Remove D2220sb from enlosure bay.
3. Power on BL460c Gen9 , entry to RBSU and Restore Manufacture Default Settings.
4. Reboot server only BL460c Gen9 and shutdown and power off.
5. Insert D2220sb to enclosure bay and wait LED to steady green lit.
6. Power on BL460c Gen9 server.
but not recognized D2220sb.
ummm....
Hi,
The setting is:
RBSU -> System Default Options -> Restore Manufacture Default Settings
One can always settings in RBSU and save them as System Default Settings and when there are further changes made to the RBSU configuration and there are issues, the System Default Settings can be used to switch the server to the settings which were saved so.
Restore Manufacture Default Settings resets the settings to factory defaults. In this instance please use this option.
Regards,
Vijayasarathy
Thank you for your Information.
but, I'm already read that Advisory and I can't fix my problem of do'nt recognize D2220sb by BL460c Gen9.
Step.2 of Advisory,
~~
Clear the ProLiant BL460c Gen 9 Server Blade NVRAM using Platform Configurator via ROM-Based Setup Utility (RBSU) and reboot.
~~
This mean is
RBSU -> System Default Options -> Restore System Default Settings
or
RBSU -> System Default Options -> Restore Manufacture Default Settings
It is correct?
If not and other operation is required then please step of Clear the ProLiant BL460c Gen 9 Server Blade NVRAM.
Hi,
Please refer to this advisory that has been released addressing this issue for further information.
Regards,
Vijayasarathy
Thank you for your information!!!
I was updated my BL460c Gen9 server firmware and try to connect D2220sb,
but don't recognized D2220sb storage via Smart Array P244br controller.
P244br's firmware update latest version but this is not fix.
c7000 enclosure bay 7 = D2220sb
bay8 = BL460c Gen9